BAKER & BELLFIELD is looking for employees for positions:
bench joiner
Working hours
full-time | Permanent
Salary
salary
Responsibility
joinery/solidsurface fabrication of parts according to Work Instructions/DWGs/Product Packs/Parts Lists
inspect First Offs with calibrated measuring devices to ensure compliance to specifications
reducing amount of product non-conformances
keep Injection Moulding machines operational by completing preventive maintenance requirements; following manufacturers instructions; troubleshooting malfunctions; calling for repairs
maintain a safe and clean working environment by complying with procedures, rule sand regulations
document actions by completing production and quality inspection forms
understand the functions of MRP system
contribute to team effort by accomplishing activities First Time Right
Requirements
experience in a manufacturing environment where health and safety has been demonstrated
ability to operate data capture on MRP manufacturing system
ability to read Technical DWGs
CSCS card
experience in Quality Inspection of First Offs
forklift Truck licence
joinery: 5 years
carpentry: 1 year
quality inspector
Working hours
full-time | Permanent
Salary
salary
Responsibility
competently operate Injection Moulding machines and meet daily output targets
inspect First Offs with calibrated measuring devices to ensure compliance to specifications
keep Injection Moulding machines operational by completing preventive maintenance requirements; following manufacturers instructions; troubleshooting malfunctions; calling for repairs
reducing amount of product non-conformances
maintain a safe and clean working environment by complying with procedures, rule sand regulations
document actions by completing production and quality inspection forms
understand the functions of MRP system
contribute to team effort by accomplishing activities First Time Right
Requirements
experience in a manufacturing environment where health and safety has been demonstrated
ability to operate data capture on MRP manufacturing system
ability to read Technical DWGs
experience setting and operating Injection Moulding machines
experience in Quality Inspection of First Offs
forklift Truck licence
plastics injection molding: 2 years
fabricator welder
Responsibility
work from engineering drawings, competently translating what is on paper into a high quality finished product that meets the exacting specifications
drive continuous improvements in all our business activities by adhering to lean practice
fulfill work schedules established by the Production Manager and Department Supervisor in a timely manner
ensure all our products are machined in line with safety critical requirements
maintain good, honest communication with the Production Manager, Supervisor and other team members to enable effective cooperation
encourage excellence in everything we do
maintain the quality and standard of work expected from all employees
develop products through a design led process to exceed our customers satisfaction, whilst reducing our environmental impact
Requirements
minimum 5 years experience MIG & TIG welding of stainless steel/aluminium/mild steel parts
ability to operate data capture on MRP manufacturing system
ability to read Technical DWGs
welding Fabricators: 5 years
machine operator
Trade
production & Manufacturing
Production & Manufacturing
Working hours
full-time | Permanent
Salary
salary
Responsibility
competently operate Injection Moulding machines and meet daily output targets
inspect First Offs with calibrated measuring devices to ensure compliance to specifications
keep Injection Moulding machines operational by completing preventive maintenance requirements; following manufacturers instructions; troubleshooting malfunctions; calling for repairs
reducing amount of product non-conformances
maintain a safe and clean working environment by complying with procedures, rule sand regulations
document actions by completing production and quality inspection forms
understand the functions of MRP system
contribute to team effort by accomplishing activities First Time Right
Requirements
experience in a manufacturing environment where health and safety has been demonstrated
ability to operate data capture on MRP manufacturing system
ability to read Technical DWGs
experience setting and operating Injection Moulding machines
experience in Quality Inspection of First Offs
forklift Truck licence
please apply with your CV to [email protected] or phone 01952 677411 for an interview
plastics injection molding: 2 years
design engineer
Trade
architecture
Architecture
Working hours
full-time | Permanent
Responsibility
generating detailed production and assembly drawings
undertaking hand calculations to support initial design development stages
providing necessary engineering support to production department and providing creative solution to the problems
developing reports and documents for DFMEA, RAMS, LCC, O&M and Test Reports
ensuring ECN and MRP systems are followed throughout the product development process
specifying and maintaining welding, bonding, testing, documents for production and approvals
designing concept and production 3D-CAD models of various products within the sector of Rail, Airport, Commercial Office and other specialised areas, using Solidworks
you will be responsible for the product development process and will be required to liaise with suppliers/customers throughout the project
Requirements
applicants must have a Degree in Design or Engineering
minimum of two-year experience in generating welding documentations for applicable standards and mechanical testing procedures is important
must have minimum of two-year Solidworks work experience in designing complex assemblies and parts
please apply with your CV to [email protected] or phone 01952 677411 for an interview.Design
minimum of two-year experience of producing technical drawings in a design job
we have no further positions but would love to hear from you: [email protected]
fabricator
Trade
construction
Construction
Working hours
full-time | Permanent
Responsibility
joinery/solidsurface fabrication of parts according to Work Instructions/DWGs/Product Packs/Parts Lists
inspect First Offs with calibrated measuring devices to ensure compliance to specifications
keep Injection Moulding machines operational by completing preventive maintenance requirements; following manufacturers instructions; troubleshooting malfunctions; calling for repairs
reducing amount of product non-conformances
maintain a safe and clean working environment by complying with procedures, rule sand regulations
document actions by completing production and quality inspection forms
understand the functions of MRP system
contribute to team effort by accomplishing activities First Time Right
Requirements
experience in a manufacturing environment where health and safety has been demonstrated
ability to operate data capture on MRP manufacturing system
ability to read Technical DWGs
CSCS card
experience in Quality Inspection of First Offs
forklift Truck licence
please apply with your CV to [email protected] or phone 01952 677411 for an interview